Hose Reel Drum

Hose Reel Drum - Hose Reel Drum

HOSE REEL DRUM
TYPE SWINGING TYPE-A 180 deg. Wall Mounted
WATER FLOW RATE MIN. 22.5 LPM at Min. 7.0 BAR Inlet Pressure
RANGE OF JET MIN. 6.0 MTRS at Min. 7.0 BAR Inlet Pressure
WORKING PRESSURE 1.2MPa (12 Bar)
SIDE DISC DIAMETER 560 mm (minimum), 18 Swg.
HUB WIDTH 230 mm Approx., 18 Swg.
HUB DIA 200 mm Approx., 18 Swg.
STANDARD Designed as per IS:884 (No BIS Marking)
RUBBER HOSE
TYPE TYPE-2 RUBBER (IS:444) TYPE-2 THERMOPLASTIC (IS:12585)
DIAMETER 20 mm DIA
OPERATING PRESSURE RANGE 7 to 10 KG/CM2
BURSTING PRESSURE 32.5 KG/CM2
NOZZLE
TYPE Gun Metal Shut-off ABS with Spray and Shut-off
END CONNECTION Hydraulically crimped with end fitting

"Minimax" hose reel type-A (Swinging 180° wall mounted) as per IS-884: latest revision and hose reel complete with all fittings. Made of high-quality mild steel powder coated in red colour, Thermoplastic Hose (IS: 12585) or Rubber Hose Reel (IS: 444) with 20 mm diameter. Nozzle (GM/ABS) hydraulically crimped to hose with metal crimping. Operating at 10 bar working pressure without leakage with flow rate 22.5 lpm at 07 bar pressure.

Know More

Look For More


FAQ's

Fire extinguishers should be located throughout the workplace and readily accessible to the employees without subjecting them to possible injury. Selection and installation vary site to site and hazard to hazard. General Placement distance as per the class of fire as per IS 2190 is mentioned below;
  • Class A, B and C Fire Hazard – Fire Extinguisher within 15 m travel distance.
  • Class D, F and Special Fire Hazard – Fire extinguisher within 10 m travel distance.
The knowledge of operating fire safety equipment and how to act during a fire emergency is of utmost importance as it equips the employees with the knowledge and skills to about the fire emergency procedures. Fire safety training shall be carried out every 12 months. In some critical circumstances, organization shall provide additional training. Factors that may prompt this include: An incident occurs in your industry/workplace, which impacts on your business and safety procedures.
Preparation is the key to an effective response to workplace fires. Fire drills are ways to prepare for exiting a building or performing emergency procedures during a fire emergency. Fire drills help prepare employees to respond quickly, calmly, and safely. Fire & emergency drills shall be conducted, in accordance with the Fire Safety Plan, at least once every six months.
Flammable liquids, solvents and gases, waste products, combustible materials, Oxidising chemicals, Pyrotechnics, Sparks, Hot work, Extractor fans, Conventional heat sources like HVAC and radiators, Frictional heat and static from machinery, electrical hazards due to exposed wires, overloaded circuits, static discharge and extension cords, faulty electrical equipment and machinery, activities such as welding and grinding, and anything that involves molten metals, etc. are an identified fire risks in an industrial environment.
Flammable liquids, solvents and gas storage, combustible material waste, Uncovered or unprotected fuel, electrical circuits, heating equipment, and smoking materials can also cause fires. Fire potential is less for Warehouse when compared to the industry. But when a fire incident occurs happens it is on a massive scale.
While you might think that your office is free from combustibles because there are no oils, gases or open flames, there are still risks present in any commercial building. Paper, wooden furniture, plastics, tissues, cleaning liquids, and even dust can catch fire. Electrical hazards such as exposed wires, overloaded circuits, extension cords, faulty electrical equipment and unprotected combustible materials are the primary risks for a fire breakout in offices.
Fire safety standards generally focus on minimizing the reaction to fire of products and materials used in different living environments such as domestic dwellings, household equipment, furnishings and electronics, buildings and different transport modes. Globally, most fire safety regulations have policies and procedures in effectively storing, managing, and disposing of fire initiating materials or activities. Different fire standards such as NFPA, NBC, BIS etc. are followed by the organizations for fire safety compliance.
BIS (Bureau of Indian Standards) has a guideline mentioning a small band of distinguishing color shall be prominently visible on the surface area of fire extinguishers. As you are aware that different types of extinguisher are suitable for specific classes of fire, band colour identifies the type of fire extinguisher and its suitability on different classes of fire.
The most feasible fire safety equipment required to have are fire extinguishers. The fire extinguisher equipment should be easily identifiable, highly visible, easily accessible, adequately charged, and regularly inspected. They should be placed high on wall surfaces and positioned near to the closest exit.
A fire risk assessment is a review undertaken of a building, office premises, or commercial complex in order to assess its fire risk and offer recommendations to make the building safer. It is a legal requirement. Any structure where people are dwelling as part of a commercial activity must have this done. The risk assessment is done by a fire safety authority from local fire service department with fire safety education, training and experience.
A qualified fire authority inspects a premise as part of a periodic fire risk assessment. The enforcement officer evaluates the fire standard compliance at the workplace and identifies the potential areas of improvement. The evaluations also reinforce the policies to ensure that no fire accident happens. The inspection verifies the efficiency of the existing fire prevention measures.